Onsite Data Center Compliance Audits | EnviroScanner

How It Works

Four Steps. A Very Short Onsite Visit.

Onsite visits are very short: the high-speed EnviroScanner requires less than an hour to scan a 1,000 m² data center. No photos are taken, and you stay fully operational throughout.

Step 01

Book

Request an audit and we schedule a partner technician for your site, anywhere in the world.

Step 02

Onsite Scan

A short visit. The EnviroScanner measures temperature, airflow and air quality at the rack intakes — no photographs needed.

Step 03

Encrypted Transfer

Measurement data is encrypted by the scanner and sent directly to our Swiss laboratory for processing.

Step 04

Certified Report

You receive a trustworthy, standards-referenced compliance report — ready to share with customers and auditors.

Why It's Different

An Assessment Is Only as Good as Its Data

This is something altogether different from a handful of fixed sensors mounted in a few racks. Rack inlets are scanned with a high-resolution, multi-parameter air quality and infrared surface scanning system — a proprietary system manufactured by Technology Care LLC in Zürich, Switzerland. The principle is simple: an assessment is only as good as the data behind it, and the more data there is, the better the assessment.

The Old Way

A Few Fixed Sensors

A small number of probes mounted permanently in selected racks
Hand-held instruments that capture only a few readings — slow compared to the high-speed scanning of the EnviroScanner
A handful of readings from a handful of fixed points
Blind spots between sensors — hot and cold zones go unseen
A coarse, low-resolution picture of the room

The EnviroScanner Way

High-Density, High-Granularity Scanning

Thousands of measurements taken across thousands of positions
Multi-parameter air quality and infrared surface scanning in one pass
Fine-grained coverage that reveals what sparse sensors miss
A detailed, high-resolution picture of every rack intake

Every report is built on thousands of data points per site — the density and granularity that makes a standards-referenced assessment genuinely meaningful.

Why Operators Choose It

A Clean Audit Trail, Without the Hassle

The audit is engineered to be fast, non-intrusive and tamper-resistant from the rack intake to the final report.

No Downtime

The scan happens at the rack face while equipment runs. A short visit, no shutdowns, no cabling, no calibration on site.

No Photos, Private by Design

No images of your facility are taken. Only environmental measurements are captured, and they are encrypted on the scanner.

Independent Swiss Lab

Encrypted data is processed by our Swiss laboratory into a certified report you can present with confidence.

Beyond Compliance

Cut Cooling Energy Costs by 20% or More — At Zero Cost

An audit does more than confirm compliance. We routinely identify how data centers can safely save 20% and more of their cooling energy costs through small, well-targeted changes to rack inlet temperatures — with no investments and no equipment changes.

20%+ Cooling Energy Savings

Precise rack-intake measurements reveal where cooling is being over-provisioned, so inlet temperatures can be raised safely within ASHRAE limits.

Increased Redundancy

Reclaimed cooling headroom means more spare capacity, strengthening resilience and giving your facility a wider safety margin.

Improved MTBF

Stable, well-balanced intake conditions reduce thermal stress on equipment, extending mean time between failures.

Early Warning

Our reports can give you advance warning of corrosion and contamination issues before they happen — so you can act before they affect your equipment.

Achieved through small changes to rack inlet temperatures only — no investments and no equipment changes required.

Sustainability

Evidence for Your ESG & Scope 3 Reporting

The same high-granularity measurements that protect your hardware also cut energy use, extend equipment life and keep hardware out of the e-waste stream — documented in a report you can put in front of an auditor.

Lower Cooling Energy & PUE

Thousands of rack-intake measurements reveal where cooling is over-provisioned, so inlet temperatures can be raised safely within ASHRAE limits — cutting cooling energy costs by 20% or more and directly improving PUE, with no equipment changes.

Extended Hardware Life

A large share of a data center’s carbon footprint is embodied in the manufacture of its hardware. Stable thermal conditions and early warning of corrosion help equipment reach its design life — avoiding premature, wasteful refreshes and reducing e-waste.

Safe Free-Cooling

Air-side economisation saves energy but draws in more outside air — and its contaminants. Independent measurement lets you pursue efficiency confidently, with evidence that corrosion and particulate risk stay within safe limits.

Defensible Disclosure

As frameworks such as CSRD and emerging Scope 3 requirements take hold, operators need independent, standards-referenced evidence — not unverified claims. Our certified Swiss-lab report documents the conditions behind extended equipment life.

Technology Care provides independent measurement and analysis — not cooling, abatement or remediation hardware. Reported cooling energy savings depend on each facility’s current configuration.

The Deliverable

One Report. Eight Critical Metrics.

Every audit returns a clear, standards-referenced report. Below is a real sample assessment of a data center — all eight metrics within recommended range.

Full sample Environmental Compliance Audit report

Air Temperature

Infrared Surface Temperature

Cooling Airflow Containment

Cooling Air Temp. Uniformity

Air Particles

Air Humidity

NOx

Total VOC

CO₂

Open Full Sample Report Book Your Audit

Global Reach

Delivered Worldwide Through Our Partner Network

Wherever your facility is, a trained partner technician can come to you. The audit method, the EnviroScanner instrument and the Swiss lab processing are identical at every location — so reports are consistent and comparable across your whole portfolio.

Local partner technicians for an onsite visit
One consistent standard at every site
Centralised Swiss lab processing and reporting
Ideal for multi-site and colocation operators

Audit My Facility

Tell us where your data center is and we will arrange a partner technician for an onsite scan.

Service partner? Join our network →

Standards Referenced

Aligned to the Frameworks That Matter

ASHRAE Thermal Guidelines 2021

ISO 14644-1

ANSI/ISA-71.04

LEED v4 (TVOC)

Reports reference the applicable editions of each framework. Confirm the relevant edition at the time of testing.

Questions

Frequently Asked

It is a short visit. The EnviroScanner takes its readings directly at the rack intakes while your equipment keeps running — there is no shutdown, no cabling and no onsite calibration.

No. No photos are needed. The scanner captures only environmental measurements, and that data is encrypted on the device before it is sent for processing.

Measurement data is encrypted by the EnviroScanner and transmitted directly to our Swiss laboratory, where it is processed into the final report. This keeps the audit trail trustworthy from the rack intake to the deliverable.

Eight environmental metrics across temperature, cooling airflow and air quality — including air particles, humidity, NOx, VOC and CO₂ — each compared to its recommended range and referenced to ASHRAE, ISO 14644-1, ANSI/ISA-71.04 and LEED. A full sample report is available above.

Yes. Audits are delivered worldwide through our partner network, using the same instrument and the same Swiss lab processing everywhere, so results are consistent and comparable across all of your sites.